SRM 20-120 Asphalt Recycler-Mini Batch Plant

The Stepp SRM20-120 Asphalt Recycler/Mini Batch Plant

 

.Do you have access to asphalt millings?

 

.Would you like to perform road repairs in the off season when the hot mix asphalt plants are closed?

 

.Would you benefit from being able to perform permanent pot hole repairs, using 300°F hot mix when the temperature is below freezing?

 

.Would the ability to create fresh 300ºF hot mix any-time of the year, at any temperature, be beneficial to your road maintenance program?

 

.Would you be interested in a machine that can recycle asphalt millings into 300ºF hot mix at a rate of 4 cu. Yds per hour?

 

.Does the ability to create custom hot mix blends sound intriguing?

 

.How about an American made machine, local service local parts, local support, and 60 years of mfg experience?

 

If you answered yes to any of these questions, the SRM20- 120 Asphalt Recycler/Mini Batch Plant from Stepp Mfg may be what you need.In our daily contact with road maintenance departments

like yours, we heard a common concern..

.

"When we use the expensive cold mix for pot hole re-pairs, it seems to last only a few days to a week at best, then we''re out there doing the same repair over and over again, there has to be a better way."

 

"How can we make permanent, cost effective road re-pairs after the hot-mix plant closes?"

 

We listened to your concerns and questions, and then our engineers took the challenge to design a portable, easy to use, and affordable machine that can recycle asphalt millings or create hot mix from raw materials at a rate fast enough to keep up with your busy road repair schedule

.

The  result  is  the  Stepp  SRM20-120  Asphalt  Recycler/ Mini Batch Plant.

 

What does it do?

The SRM20-120 will recycle asphalt millings into new 300°F hot mix at a rate of up to 4 sq. yds. per hour (aprox 16000 lbs). This rate can be achieved even at an outside temperature of 20°F giving you usable production rates year round.

 

Custom mixes from raw materials can also be created with the SRM20-120. Different sized aggregate, chips, or even sand, can be used to make the perfect mix for your special needs.

The SRM20-120 uses an indirect method of heating. The flame does not come in contact with the materials being heated. This indirect method of heating reduces smoke emissions, burning off the oils from your millings, and fire dangers.

 

The indirect heating method allows approx 90% of the oils to be retained. Thus only about 1½ to 1¾ gallons of oil need to be added for each yard of recycled millings. The on-board heated kettle has a capacity of 120 gallons allowing you to recycle about 50 to 60 yards without refilling the kettle. Of coarse if you are creating hot mix from raw materials the oil use will be higher.

 

Operation

The machine is completely self-contained and portable. A properly equipped ¾ ton pickup or larger truck is needed to pull the unit. The SRM20-120 is equipped with two (2) 6000 lb. axles, electric brakes, and DOT approved lighting for safe and easy transporting. Once on site, it takes only a few minutes to lower the four (4) landing gear legs to stabilize the unit for operation.

 

Millings are loaded into the 10foot wide hopper on top of the machine with a skid steer or other type of wheel loader .All heating controls are located in the control panel on the right rear of the machine. Operation of the heating system only requires the power switch to be placed in the ON position and the thermostat for the kettle portion of the machine to be set to the desired temperature.

 

The feed, mixing, and blending rates are all controlled from the same control panel as the heating system for convenient operation of the machine. Once the SRM20-120 is at operating temperature and the feed rate controls are adjusted properly, no further steps are required to operate the machine other than monitoring the operation and perhaps making minor adjustments to the feed rates. Of course you have to load millings into the machine... then recycled asphalt continuously discharges from the rear of the machine onto a loading conveyor allowing you to fill your Stepp Pre-Mix Heater or other insulated hopper used to haul the hot mix to the site of road repair.

相关新闻
企业新闻专题 - 海川新材
国内沥青动态
厂家分布
icon_top 一周资讯关注排行榜