Terex/CMI PR600 Cold Planers
With a 600-hp diesel engine and operating weights approaching 91,200 pounds, the three- and four-track Terex/CMI PR600 cold planers from Terex Roadbuilding are designed for high-production milling and rehabilitation of asphalt surfaces.

• Center-mounted cutter design
• 10-degree tapered front and rear moldboard design
• 48-inch-diameter cutter with 177 tungsten carbide teeth
• 86-inch cutting width
• Four working speed ranges
• Proportional joystick steering with four steering modes
• Pleated 42-inch-wide high-capacity upper and lower conveyors

             Terex/CMI PR600 Cold Planers

Process Heating Patch King
The Patch King asphalt patchers heat mix to a precise temperature during the night.

• Rotary auger model PK-40HSD features reversible rotary conveyor that is driven by a hydraulic motor and supported by heavy-duty ball bearings
• Mix/anti-bridging device features separate hydraulic drive and controls
• Wear parts, including auger and trough, are easily replaceable
• Reversible auger feeds patch mix to work area to eliminate dump beds and hoists

            Process Heating Patch King

VSS Macropaver 12B
The VSS Macropaver 12B truck-mounted slurry/microsurfacing machine offers an average output of 3 to 4 tons/minute.

• 12-cubic-yard maximum aggregate capacity
• Hydraulic fail-safe automatic materials sequencing
• Seal Lock hydraulics
• Fines feeder power and drive system offers increased power and a simpler, robust design
• Tier II electronically-controlled engine
• 850-gallon water and emulsion tanks
• Options include CALTRANS material monitoring and control system; truck speed control on operator platform; stainless-steel additive tank/pump system; high-pressure washer/reel; and more

            VSS Macropaver 12B

BOMAG Cold Planer Milling Machines
The BM1000/30 and BM1300/30 feature centrally mounted cutting drums that allow precise milling next to walls, curbs and other obstructions.

• 275-hp Caterpillar diesel engine
• Cutting drum with direct mechanical drive design provides 39.6- and 51.4-inch standard cutting widths with up to 12.6-inch milling depths
• Centrally located "over-the-cut" operator''s position and sliding operator''s seat ensure better jobsite visibility

            BOMAG Cold Planer Milling Machines

Caterpillar PM-201 Cold Planer
Caterpillar''s PM-201 features a 650-hp Cat C18 engine with ACERT technology.

• 83-inch rotor width
• 12-inch rotor depth
• 41,310-pound operating weight
• Load Sensing Propel System
• Choice of three rotor designs
• High capacity, versatile conveyor

              Caterpillar PM-201 Cold Planer

Neupauer NI-3 Pothole Patcher
The NI-3 Pothole Patcher from Neupauer Industries is a complete mobile system for accurate proportion, drying, heating, mixing, and delivering hot asphalt paving and patching compound to your jobsite.

• Liquid Asphalt Cement (AC-20) is pumped into the heated end of the drum to mix with sand and aggregate
• With the volumetric mixer, you can start and stop with any amount
• AC tank holds up to 220 gallons and is heated by propane or fuel oil

                  Neupauer NI-3 Pothole Patcher

Bergkamp Slurry Seal/Microsurfacing Pavers
Bergkamp''s slurry seal/microsurfacing truck-mounted continuous pavers feature a spreader box, including a variable width spreader box.

• Carries up to 10 cubic yards of aggregate, 600 gallons of emulsion and water and 55 gallons of additive
• Pugmill, conveyor and all liquid material tanks are removable for easier maintenance
• Flexibility in meeting legal load weight restrictions with the addition of up to three tag axles — including one behind-the-drive axle
• Full-width platform allows operators to see both sides easily
• Remote sideshift control lets the spreader box operator control the box from the ground

              Bergkamp Slurry Seal/Microsurfacing Pavers

Wirtgen W 1500 Milling Machine
The W 1500 milling machine''s diesel engine delivers an output of 435 continuous horsepower and high torque stability.

• Milling drums available with 4.25- or 5-foot working widths.
• 51- to 60-inch standard cutting width or 60-inch maximum width
• 12-inch cutting depth
• 97-fpm operating speed
• 55,953-pound operating weight

        Wirtgen W 1500 Milling Machine